Skip to content
Back to Integrations

Procore + Sage 100 Contractor

Procore and Sage 100 Contractor, without the workarounds.

Procore's Sage 100 Contractor connector covers the standard path between project management and accounting. We close the gaps it documents (truncated names, vendor details, sub jobs, project-specific cost codes), so the two systems stop needing manual clean-up.

Written by Roberto Postolovski, Founder & Tech LeadUpdated

Today

How it works now

The connector syncs the job. The exceptions are handled by hand.

For contractors on Sage 100 Contractor who manage projects in Procore.

  1. 01A project is created in Procore and its name is cut to 30 characters in Sage.
  2. 02The export fails because the project address contains a comma.
  3. 03A vendor is exported and the accounting approver types its ERP vendor ID by hand.
  4. 04Vendor phone numbers are entered twice.
  5. 05A sub job is planned in Procore but has to be created in Sage first, then imported.

The native connector

Where Procore's Sage 100 Contractor connector stops

From Procore's own documentation for its Sage 100 Contractor connector:

Sources

  • Project names longer than 30 characters are truncated.
  • Commas aren't allowed in the project address field.
  • Vendor phone numbers aren't included on import or export, and the ERP vendor ID is entered manually when a company is exported.
  • Project-specific cost codes aren't supported. Every project cost code must come from the synced standard list.
  • Sub jobs are import-only, from Sage 100 Contractor to Procore.
  • Budget changes are export-only, from Procore to Sage 100 Contractor.
  • Once a project is synced, commitments must be created in Procore.
  • Sage 100 Contractor version 20.5 or later is required, and Sage 100cloud isn't supported.

The automation

How we replace it

We validate before the connector runs and fill in what it leaves out.

  1. 01

    Audit

    Which of the documented limits cause manual work for your team, and how often.

  2. 02

    Validate

    Names, addresses and cost codes are checked against Sage 100 Contractor's rules when they're entered in Procore, so exports don't fail later.

  3. 03

    Enrich

    Vendor IDs and phone numbers are filled in from the system of record instead of typed by hand.

  4. 04

    Extend

    Sub jobs and cost structures the connector can't carry are handled through a supported route, agreed before the build starts.

  5. 05

    Approve

    Exports to Sage stay behind accounting approval.

  6. 06

    Monitor

    Every sync is logged, and failures surface the same day with the reason attached.

Typical gaps we close

  • Project names over 30 characters
  • Addresses with commas
  • Vendor phone numbers and IDs
  • Sub jobs created in Procore
  • Project-specific cost codes
  • Budget changes in both directions

Systems involved

  • Procore
  • Sage 100 Contractor
  • Excel
  • Microsoft 365

What stays with your team

Automation should remove the repetition, not the responsibility.

  • Approval of exports to Sage
  • Vendor and cost code master data decisions
  • Sub job structure
  • Records that fail validation

What changes

Measured against your own baseline, not against a benchmark.

  • Exports stop failing on names, addresses and IDs
  • Vendor details are entered once
  • Sub jobs and cost codes follow one consistent structure
  • Fewer manual corrections in Sage after every sync

Questions

Common questions

We're on Sage 100cloud. Does this work?
Procore's connector doesn't support Sage 100cloud. That doesn't rule out an integration, but the route is different, and we confirm it before quoting.
Can't we just keep project names short?
You can, and many teams do. Validating names in Procore at the moment a project is created makes that rule automatic instead of something people have to remember.
Do you replace Procore's connector?
No. It stays in place for what it covers. We add validation and the pieces it leaves out.
What access do you need to Sage 100 Contractor?
The minimum needed for the records in scope, agreed in writing before work starts. Where possible, access is read-only, with writes going through supported imports or the connector itself.

What’s one repetitive process your team does every day?

Tell us about it. We’ll help you determine whether it can be automated, what it would take, and whether the numbers make sense.